Viewed products
With the Ripcord USB power cable, you have the...
With the Ripcord USB power cable, you have the freedom to power anywhere you are any device in 5, 9 or 12V from a USB port of a laptop, from an external battery or from a smartphone/tablet (with OTG cable).
The connector is on one side USB A Male, to connect to a laptop eg. and on the other side standard 5.5mm jack connector with the positive (+) polarity in the center and the negative (-) polarity on the outside.
Maximum amperage on the 5V version: 2.4A
Maximum amperage on the 9V version: 1A
Maximum amperage on the 12V version: 0.750A (750mA)
Ripcord cables are compatible with USB 1.0, 2.0 and 3.0 ports as long as you do not exceed max power of 9W.
For example, the 12V Ripcord cable can be used to power a to power a BIAS-TEE for LNB to QO-100 from a laptop or external battery.
Come with: 1 Ripcord cable in 5, 9 or 12V, to choose below.
Voltage: 5, 9 or 12 volts
Output connector: Standard 5.5mm jack (positive (+) polarity in the center and negative (-) polarity on the outside)
Maximum amperage on the 5V version: 2.4A (2400mA)
Maximum amperage on the 9V version: 1A (1000mA)
Maximum amperage on the 12V version: 0.750A (750mA)
Ripcord cables are compatible with USB 1.0, 2.0 and 3.0 ports as long as you do not exceed max power. from 9W.
The Ripcord 5V, 9V or 12V USB power cable is a project that has been funded collaboratively in crowdfunding via the Kickstarter platform.
Reference: CABLE-COAXIAL-UHF-M-1M-876
UHF Male - UHF Male coaxial cable extension with KSR195 low-loss 50 ohm coaxial cable for use from 0 to 6 GHz. Available lengths: 50cm, 1, 2, 3, 5 or 10, 15 and 20 metresConnector 1: UHF Male
Reference: PIGTAIL-SMA-M-SMA-F-15CM-996
This low-loss pigtail cable in RG316 converts a SMA Male connector to an SMA Female connector. Available in 15cm, 50cm or 1 metre.
Reference: PIGTAIL-SMA-M-SMA-M-81
SMA Male to SMA Male pigtail adapter, for connecting a card, for example converter Ham it upconverter card to the SDR transceiver HackRF One SDR transceiver, or the SDRPlay broadband receiverwideband
Reference: NAGOYA-L20-UHF-456
This dummy load 50 ohms Nagoya L20 runs from 0 to 500MHz with a maximum power of 15W or 100W (during 2 seconds max), with UHF male connector (PL-259) or N male plug (choose below). Genuine Nagoya
Reference: CABLE-MICRO-USB-BLANC-0451
This USB to micro USB cable measures 1 metre and can be used as a power cable for BlueDV, Raspberry Pi board, Samsung S3, S4, S5 mobile phone or any device with a micro-USB power port. Available in
Reference: CRT-CABLE-MIDLAND-T060-446
This original radio power cable for CB transceiver and compatible with 12V supply 3-pin citizen band transceiver. Comes with: Power cable 12V Midland T060.
Reference: NISSEI-NS-1230D-710
Compact digital switching power supply NISSEI NS-1230D, 13.8V (or adjustable from 4 to 16 volts), 30A Max., with Power-Pole connector on the rear panel and heavy-duty connection terminals on the
Reference: NISSEI-NS28SW-716
Compact digital switching power supply NISSEI NS-28SW, 13.8V (or adjustable from 9 to 15 volts), 28A, with heavy-duty connection terminals on the rear panel.Protection against short circuits and
Click here to leave a review
Be the first to ask a question about this product!
This USB to micro USB cable measures 1 metre and can be used as a power cable for BlueDV, Raspberry Pi board, Samsung S3, S4, S5 mobile phone or any device with a micro-USB power port. Available in
1,63 €tax excl.
This original radio power cable for CB transceiver and compatible with 12V supply 3-pin citizen band transceiver. Comes with: Power cable 12V Midland T060.
4,92 €tax excl.
Compact digital switching power supply NISSEI NS-1230D, 13.8V (or adjustable from 4 to 16 volts), 30A Max., with Power-Pole connector on the rear panel and heavy-duty connection terminals on the
140,83 €tax excl.
Compact digital switching power supply NISSEI NS-28SW, 13.8V (or adjustable from 9 to 15 volts), 28A, with heavy-duty connection terminals on the rear panel.Protection against short circuits and
94,83 €tax excl.
This BT4G-based BIAS-TEE with SMA female connector is used to power a LNA or a 10Ghz PLL LNB to receive the QO-100 / Es'Hail2 satellite.The BT4G covers the frequency bands from 30 MHz to 4 GHz. The
14,58 €tax excl.
Simple adapter for connecting a micro-USB power supply to a USB-C type device, such as the Raspberry Pi 4, Samsung S8, S9, or any USB-C device.
1,56 €tax excl.
Raspberry official power supply for Rpi 4 with USB-C plug, with EU power adapter plug.Supplied with: 1 Raspberry Pi 4 power supply, EU plug, original warranty.
9,71 €tax excl.
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal
Copyright 2014-2024 - Passion Radio / 4 MY PEOPLE.
Les photos et coloris ne sont pas contractuels.