> Ham & radio equipment>PC radio interface>Signalink-SLUSB-8R + SLMOD-8RI pack for ICOM with 8-pin mic jack
Signalink-SLUSB-8R pack for Kenwood & Alinco with 8-pin mic jack View larger
Tigertronics

SIGNALINK-PACK-SLUSB8RI-1708

New product

U.S.A

Signalink-SLUSB-8R + SLMOD-8RI pack for ICOM with 8-pin mic jack

rating Read the 2 reviews
Average rating: 5/5 Number of reviews: 2

The Signalink SLUSB-8R + SLMOD-8RI interface pack is compatible with ICOM radios equipped with an 8-pin micro such as ICOM : IC-707/718/720/725/726, IC-728/729/730/735, IC-736/737/738/740/745, IC-746/746PRO, IC-756/756PRO, IC-756PROII/PROIII, IC-7400/7700/7800, IC-751/761/765/775/781, IC-820H/901 /910.

  • Low noise USB sound card
  • Quick and easy installation with the jumper
  • RX and TX setting from the front panel
  • Support ALL digital and digital modes such as SSTV, RTTY, Packet, PSK, ROS, FT8, FT4, JS8, ACARS, etc.
  • Complete RF isolation between computer and radio
  • Transmit Audio output and external speaker jack

The pack includes: 1 Tigertronics Signalink USB interface, 1 SLCAB8R cable to connect the radio to the interface and the SLMOD8RI jumper to be installed inside the interface, 1 USB cable 2.5m, 1 mono jack cable, 6 pre-cut and stripped 24 AWG wires, 1 Allen key - 3/32 "size, rubber feet, 1 English manual.

Note: This interface does not allow frequency control (CAT control) on the radio station used, it allows switching to PTT and sending a signal to the radio station and receiving it, thanks to the USB peripherals created.

More details

157,50 € tax excl.

Instead of 160,67 €

Out of stock, available within 1-2 months

Pack content

Download

Signalink cable jumper guide FR

Guide in French to choose the right radio cable and jumper according to the brand and model of the radio used. 177.6k

Signalink cable jumper guide EN

Guide in English to choose the right radio cable and jumper according to the brand and model of the radio used. 666.13k

Manual Signalink USB (FR)

French manual and user guide Signalink USB 1.48M

Manual Signalink USB (EN)

English manual and user guide Signalink USB. 745.98k

Réglages Signalink (FR)

1.2M

Data sheet

  • Power supply: USB port compatible with USB 1.1 / 2.0 / 3.0, Male B connector
  • Consumption: ~ 140mA in transmission, ~ 80mA nominal
  • Operating temperature: -30° C to + 60° C
  • Audio frequency response: 200 Hz - 4000 Hz at 600 ohms
  • Sampling rate: 16 Bits, up to 48Khz
  • Operating System: Windows 98SE, ME, 2000, XP, Vista, Windows 7, 8.x and Windows 10
  • MAC OS 9.1, MAC OS X 10.00
  • Z radio input / output: 600 Ohm
  • Auto-PTT ™ delay: 30 ms to 3 seconds
  • PTT circuit: Relay, rated value - 1A @ 24VDC (max), 0.5A @ 120VAC (max)
  • Radio connection: Audio TX, Audio RX, PTT, GND and RJ-45 female
  • RX audio / speaker: 3.5mm mono jack mono
  • Housing: Extruded aluminum, powder coated
  • Dimensions: 40 x 81 x 91 mm
  • Weight: 187g

Compatible radio

This Signalink pack is compatible with the radios below and the European or American versions.

ICOM
IC-1201/1271/1275
IC-22U/25/27/28
IC-228/229/251AE
IC-255/260/271/290
IC-2400/2500
IC-37A/38A/375
IC-3200/3210/3220
IC-45/47/48
IC-471/475/490
IC-505/551/560/575
IC-707/718/720/725/726
IC-728/729/730/735
IC-736/737/738/740/745
IC-746/746PRO
IC-756/756PRO
IC-756PROII/PROIII
IC-7300/7400/7700/7800
IC-751/761/765/775/781
IC-820H/901 /910

PWR / SPKR Jumper Settings - To maintain compatibility with as many radios as possible, this jumper module has two small jumpers that can be set to activate the power and audio speaker.

PWR - This jumper is *NOT* used with the SignaLink USB, but can be installed to power the older SignaLink SL-1 or SL-1+ model from your radio if there is enough power available on pin #2 of the Mic connector (check your radio's manual).

SPKR - This jumper should only be installed if your radio has an audio speaker on pin #8 of the Mic connector (check your radio manual).  If the audio speaker is not available, you will need to connect an audio cable between the radio and the SignaLink as described in the SignaLink installation manual.

The SignaLink USB supports virtually ALL digital modes that are available for sound card interfaces including but not limited to, PSK31, MT-63, WSJT/WSJT-X  modes (FT8, JT4, JT9, JT65, QRA64, ISCAT, MSK144, WSPR, JTMS, FSK441, FSK315, ISCAT, and JT6M.), SSTV, APRS ®, Packet (300 and 1200 baud), VARA HF, VARA Narrow, and VARA Wide.

The SignaLink USB also supports virtually ALL Voice modes (VOIP, RoIP, etc.), such as EchoLink®, and Zello. 

About the only modes that you can't operate with the SignaLink USB, or any other sound card interface, are Pactor, G-TOR and Clover.

  • Customers also bought

    No products available

  • We also recommend

Reviews

Click here to leave a review

rating 5
Signal link USB
Parfait pour la livraison, parfait pour la mise en place, parfait pour l\'utilisation.
Couplage a un Kenwood TS 2000
rating 5
Satisfait
Fonctionne de manière impeccable. Paramétrage un peu complexe, mais on y arrive

Questions

Be the first to ask a question about this product!

Question about the product

* Required fields
(read)

Additional or similar equipment

Delivery Europe & Overseas

Stock and shipped from France

Product return

14 days to return, 2 warranty

Email support

Response within 24h to 72h

Secure payment

SSL, VISA, Mastercard, Paypal

Copyright 2014-2024 - Passion Radio / 4 MY PEOPLE.
Les photos et coloris ne sont pas contractuels.