Balun HF 1:1 QRO M0CVO 1.8-54Mhz 1kW (CW) 1.2kW (PEP)

Additional or similar equipment

• 

  HF Antenna Balun 1:9 for SDR

  This balun is the perfect accessory to connect a long wire antenna, for example with the converter HF SDR Ham it Up to listen shortwave and HF bands from 0.5 to 30Mhz, but this balun can work up to

  18,86 € tax incl.

  15,72 €tax excl.

  In stock
• 

  Balun 1:1 HF 1.7Mhz à 40Mhz Diamond BU50/A

  Diamond BU50/A balun 1:1, genuine, operates from 1.7 to 40Mhz and allows to receive and transmit on HF bands.Technical data sheet of the HF BU50A balun:● Operating frequency from 1.7 to 40MHz●

  36,83 € tax incl.

  30,69 €tax excl.

  In stock
• 

  Balun 1:1 HF+6M from 3 to 75Mhz Diamond BU55

  Genuine Diamond BU55 balun 1:1, operates from 3 to 75Mhz, allows to receive and transmit on HF bands + 6 meters (50Mhz).Technical data sheet of the HF BU55 balun:● Operating frequency from 3 to 75MHz●

  39,90 € tax incl.

  33,25 €tax excl.

  In stock
• 

  Low-loss coaxial cable extension UHF Male (PL-259) KSR195

  UHF Male - UHF Male coaxial cable extension with KSR195 low-loss 50 ohm coaxial cable for use from 0 to 6 GHz. Available lengths: 50cm, 1, 2, 3, 5 or 10, 15 and 20 metresConnector 1: UHF Male

  9,90 € tax incl.

  8,25 €tax excl.

  In stock
• 

  Nooelec Balun 1:9 V2 for HF SDR reception 0-30Mhz

  The new version Nooelec Balun 1:9 v2 allows to add a wired or dipole antenna type to listen HF bands from 0 to 30Mhz from the Ham It Up converter, an SDRPlay receiver or equivalent covering the HF

  24,29 € tax incl.

  20,24 €tax excl.

  In stock
• 

  RG58 coaxial cable extension with UHF Male (PL-259)

  UHF Male - UHF Male (PL-259) coaxial cable with RG58 MIL-C-17 50 ohm connector for frequency use from 0 to 1000Mhz. Available in different lengths: 30cm, 50cm, 1m or 2 metres. Connector 1: UHF Male

  7,50 € tax incl.

  6,25 €tax excl.

  In stock
• 

  RG58 coaxial cable extension with BNC Male and UHF Male (PL-259)

  Coaxial patch cable with BNC Male - UHF Male connector (PL-259) with RG58 MIL-C-17 50 ohm coaxial cable for use in frequencies from 0 to 1000Mhz. Available in different lengths: 50cm, 1m or 2 metres.

  6,90 € tax incl.

  5,75 €tax excl.

  In stock
• 

  Balun 1:1 M0CVO HF 1.8 to 30MHz 400W PEP

  The M0CVO high power 1:1 Balun operates from 1.8 to 30MHz. It can handle up to 400W PEP (CW or SSB). It is used to match a balanced antenna, such as a dipole, to an unbalanced feed such as coaxial

  45,90 € tax incl.

  38,25 €tax excl.

  Out of stock, available within 2 to 3 months
• 

  Balun 4:1M0CVO HF 1.8-54Mhz 400W PEP

  The M0CVO high power 4:1 Balun operates from 1.8 to 54MHz. It supports up to 400W CW or 500W PEP in SSB. It is used to convert the 200Ω impedance seen at the feed point of a bent or off-centre fed

  45,90 € tax incl.

  38,25 €tax excl.

  In stock
• 

  Balun HF 9:1 UNUN M0CVO 1,8-54Mhz 400W PEP

  The M0CVO 9:1 UNUN Balun operates from 1.8 to 54MHz and supports up to 400W PEP (CW or SSB) and 50-60W max. en FT8, AM ou RTTY. It provides a power point for a long-wire radiating element and converts

  47,90 € tax incl.

  39,92 €tax excl.

  In stock
• 

  Balun 4:1 HF QRO 1.8 to 54Mhz 1kW M0CVO

  Balun 4:1 QRO for very high power M0CVO Antennas for Windom antennas, dipoles, fed loops or folded off centre. RF power of 1kW, for intermittent amateur use and not for continuous AM broadcast use nor

  74,72 € tax incl.

  62,27 €tax excl.

  In stock